Kontraktor-Jasa-Pemasangan-Peredam-Suara-Ruangan-TG-Acoustic

Spesialis Peredam Suara Ruangan Soundproofing Specialist, Accoustic Design & Interior Specialist,  Thermal Insulation

Studio Soundproofing: How It Works, the Right Materials, and the Correct Installation Order

Two Separate Problems That Are Routinely Treated as One

Most studio design mistakes start here: the owner assumes one solution covers two problems that actually have different causes and different fixes.

What is the difference between noise control and acoustic treatment for a studio?
Noise control is the work of isolating a room from outside sound, or preventing sound from leaking out. Acoustic treatment is the work of controlling reflections inside a room so it does not ring or echo excessively. A serious studio needs both at the same time: good isolation keeps bass from leaking to the neighbors, while proper treatment makes recordings sound clean without room-echo artifacts.

Consider a studio in a Bali villa: double-layer thick brick walls, ventilation open to the garden, and a high ceiling typical of tropical architecture. The owner reports that vocal recordings sound reverberant and “like a bathroom.” The problem is not isolation. There is simply no acoustic treatment. Reflections off hard walls and the high ceiling create a long reverb tail that destroys recording clarity.

Then there is a premium Jakarta apartment studio covered wall to wall in foam panels. The kick drum and bass guitar are still clearly audible in the adjacent unit. Foam panels reduce echo inside the room, but they carry no mass to stop low-frequency energy from passing through concrete. That is a noise control problem, and acoustic treatment does not solve it.

These two cases are not exceptions. They are the most common pattern when a room is finished and the result does not meet expectations. Understanding the difference between the two problems is the first step before choosing any material or construction method.


Studio Soundproofing Materials: What Each One Does and Why You Choose It

Material selection is not about brand or price per sheet. It is about where the material is placed and which frequencies need to be addressed. Below are the four primary materials used in studio projects, with their function and installation position.

Rockwool

Rockwool is a mineral fiber made from basalt rock or slag steel. At a density of 60 to 80 kg/m3, it absorbs mid-to-high frequency sound energy inside wall cavities. Rockwool is not applied directly to a visible wall surface. It is packed into the cavity between two structural layers. A thickness of 5 to 10 cm inside an air cavity provides meaningful absorption, particularly at frequencies of 500 Hz and above.

Glasswool

Glasswool operates on the same principle as Rockwool but weighs less. It is more commonly used in suspended ceiling construction or lightweight partitions where structural load is a consideration. Like Rockwool, glasswool has limits at very low frequencies. Both are absorptive materials, not mass barriers.

Mass Loaded Vinyl (MLV)

MLV is a thin, high-mass layer that acts as a sound barrier, not an absorber. It is added between gypsum layers or at the wall surface to increase mass without sacrificing too much total wall thickness. MLV is most relevant when the isolation target includes low frequencies below 250 Hz, because low-frequency energy requires mass to stop it. Combining Rockwool in the cavity with MLV on the surface layer outperforms doubling the thickness of either material alone.

Layered Gypsum

Gypsum is not an absorptive material. It is a cladding material that adds mass and stiffness to wall construction. In studio design, gypsum is typically installed in two or more layers, with MLV in between. This approach significantly increases the wall’s Sound Transmission Class (STC) compared to a single gypsum layer. The seams between layers must also be staggered so there is no aligned weak point running through the wall.

To understand how each of these elements interacts, read the full guide on acoustic components of a music studio room, which covers each layer in greater detail.


Why Installation Order Determines the Outcome

This is the step most often ignored in studio projects that proceed without acoustic planning. Construction sequence is not a matter of preference. It is a matter of physics.

The Room Within a Room Principle

A studio that requires full isolation is built on the principle of a room within a room: a construction box that sits on a foundation decoupled from the original building structure, with walls that do not touch the existing walls, and a ceiling that does not connect directly to the building’s ceiling. This principle cuts off the path of structural vibration transmission.

The sequence cannot be reversed:

  1. The floor is decoupled first. A floating floor is built on a vibration isolation layer before the new studio walls are erected. If the walls go up first and touch the original floor, all vibration from inside the studio will travel into the building structure.
  2. The new walls are built on top of the floating floor. These walls must not touch the existing walls. The air gap between them is part of the isolation system, not a construction error.
  3. The suspended ceiling is built last. Resilient hangers ensure the studio ceiling does not transfer sound to the building ceiling above it.
  4. Acoustic treatment is installed after the isolation construction is complete. Acoustic panels, absorbers, and diffusers go on the surfaces of the already-isolated room, not before.

Installing acoustic panels by type and function over an existing wall does not fix sound leakage. Acoustic panels only correct echo inside the room. If the isolation construction is not in place, sound will continue to leak out even if every wall surface is covered with panels.

Without decoupling, a floating floor, and double-leaf construction executed in the correct order, no amount of material spending will produce meaningful isolation.


Studios in Existing Buildings: Constraints to Understand from the Start

A new build gives you the freedom to plan acoustics from scratch. An existing building brings compromises that must be understood early so that expectations stay realistic.

Constraints in Existing Villas and Houses

Bali villas typically have open ventilation, solid brick walls with no cavity, and timber-framed ceilings that are not easy to modify. Adding a studio to this kind of building allows for a significant improvement in isolation, but the result will not equal a building designed acoustically from the ground up. The ceiling cannot be dropped too far because headroom is already limited, and existing concrete walls are not easily retrofitted with cavities without partial demolition.

Constraints in Premium Apartments

Apartments carry two related constraints. First, building management rules commonly prohibit structural changes, drilling at certain points, or adding floor loads beyond design tolerance. Second, the existing concrete structure transmits sound through mass and structural vibration, not just through air. An ideal floating floor requires both space and permissions that are often unavailable.

What is achievable in an existing building is meaningful reduction, not total isolation. This is not a design failure. It is a physical and regulatory limitation that needs to be communicated before the project starts, not after the final measurement is taken.

Industry standards used to measure the performance of recording rooms can be referenced from the International Society of Acoustics guidelines as an independent technical reference.


When to Survey Before Choosing Any Material

The short answer: before buying anything.

Choosing materials without a site survey risks inefficient spending. Rockwool purchased in large quantities will not perform as expected if the wall cavity is not planned correctly. MLV installed without understanding the main sound leakage paths will only fix a small part of the problem.

A survey examines things that cannot be assessed from photos or floor plans, including:

  • Existing wall and floor materials, including whether cavities already exist or can be created
  • Weak points for sound leakage: doors, ventilation, structural joints, and electrical or pipe conduit paths
  • A realistic RT60 target for the type of studio planned, whether a dead room, a live room, or both
  • Physical room constraints: minimum ceiling height after construction, and how much wall thickness can be sacrificed for isolation cavities

If you are planning a recording room or music studio, start by reading more about music studio soundproofing services to understand the scope of available work before deciding on the next step.

TG Acoustic provides free surveys for the Jabodetabek area. For Bali and other cities, surveys are available by prior scheduling. Schedule a free Jabodetabek survey and get a clear picture of your room’s condition before committing to any material or construction method.


Frequently Asked Questions

Are egg-crate foam or pyramid foam panels enough for a recording studio?

No. Egg-crate and pyramid foam panels absorb only part of the energy in mid and high frequencies and carry no mass to stop sound from passing through walls. These materials can reduce light echo in a very small room, but they will not meet any reasonable recording studio standard because low frequencies and structural leakage are left completely unaddressed. Proper studio work starts at wall construction, not at the wall surface.

How thick should Rockwool be for a studio wall?

Rockwool for studio walls typically runs 5 to 10 cm thick, at a minimum density of 60 kg/m3, to absorb mid-range frequencies effectively. Thickness alone is not enough: the Rockwool must sit inside an air cavity between two wall layers, not applied directly to a surface. The exact figure depends on your target dB reduction and the frequencies causing the problem, which can only be confirmed after a site survey.

Can a studio in an apartment be completely soundproof?

Relatively, not absolutely. Apartments have two core constraints: building management rules that restrict structural changes, and existing concrete structure that carries sound through mass and vibration. What is achievable is significant reduction, not total isolation. Floors are especially difficult because a floating floor requires space and is often prohibited by management. A consultation with baseline measurements is the realistic first step before setting any target.

What is decoupling and why does it matter for a studio?

Decoupling means breaking direct contact between two building surfaces so that vibration cannot travel structurally. Examples include a studio wall built on a rubber vibration pad, or a ceiling hung on resilient hangers so it does not connect to the building’s original ceiling. Without decoupling, bass and instrument vibration from a subwoofer will travel through the building structure even if the walls are filled with absorptive material.

When do I need Mass Loaded Vinyl in addition to Rockwool?

MLV is needed when the isolation target covers low frequencies, especially bass below 250 Hz. Rockwool works well for mid and high frequencies but has limits at low frequencies because that energy requires mass to stop it, not fiber. MLV is added as a barrier layer on top of or between gypsum layers, adding mass without sacrificing too much wall thickness. The combination of both outperforms doubling the thickness of either material alone.


Next Steps

A studio that works is not about the most expensive materials or the most panels. It is about the correct sequence: structural isolation planned before construction begins, materials chosen to match the problem frequencies, and acoustic treatment installed after isolation is complete.

If you are planning a studio in a villa, house, or apartment and are not yet sure where to start, a room condition survey is the most efficient starting point. Knowing your building’s limitations before choosing materials is far better than finding out after everything is installed.

Schedule a free Jabodetabek survey and consult on your studio room with the TG Acoustic team. For Bali and other cities, scheduling is available through the consultation form.

Copyright © 2026 TG Acoustic - Spesialis Peredam Suara Ruangan